What is happening in your workshop...?

If you're having a problem with your scoot, drop us a line!

Moderator: Tuna Cowboy

What is happening in your workshop...?

Postby spiderwebb » Fri Jan 20, 2012 9:14 pm

post up what your up to...!!









:roll: :roll:
I'm just messing with jetting and could stop by to fumigate your roses...
User avatar
spiderwebb
 
Posts: 2661
Joined: Fri May 25, 2007 3:15 pm
Location: Eugene, OR

Re: Whati s happening in your workshop...?

Postby jeffreyned » Fri Jan 20, 2012 10:26 pm

I need to organize my garage. Lately I've been scooting around the block every time the rain stops for a minute and thinking about wiring up the signal lights on my P.
User avatar
jeffreyned
 
Posts: 1219
Joined: Sat May 07, 2011 7:52 pm

Re: Whati s happening in your workshop...?

Postby joe » Fri Jan 20, 2012 10:47 pm

This weekend: cleaning, decoking and painting the exhaust for the white gs. Tightening the forks on the Li. Installing new front shock and new front brake cable in the white gs.
____________________________________
Friends Don't Let Friends Ride Tupperware
User avatar
joe
Site Admin
 
Posts: 8239
Joined: Tue Apr 25, 2006 10:06 pm
Location: Sunny Eugene, Oregon

Re: Whati s happening in your workshop...?

Postby Gearless42 » Sat Jan 21, 2012 10:53 am

transporting Goofs GL over here and starting in on a rebuild. Port mapping a modded 166 kit and maybe altering my exhaust timing
If you keep fiddling with it, it's going to fall off...
~Landon
User avatar
Gearless42
 
Posts: 579
Joined: Sat Sep 25, 2010 11:21 am
Location: Eugene, Or

Re: Whati s happening in your workshop...?

Postby Tuna Cowboy » Sat Jan 21, 2012 12:20 pm

some cleaning and trying to get the "paying" jobs out, ruckus, triumph, passport. maybe chillin with landon.
Cheers,
Geoff
User avatar
Tuna Cowboy
Forum Moderator
 
Posts: 4976
Joined: Mon May 01, 2006 6:21 pm
Location: Eugene, Or

Re: Whati s happening in your workshop...?

Postby Miguel » Sun Jan 22, 2012 7:43 am

I'm off-Hoping to finish building a fork for the GS 160. Next week get the ignition and wiring fine tuned on my blue VBB, it looks too good to be just sitting in the garage. Did you figure out the problem with the GL?
Miguel
 
Posts: 1170
Joined: Tue May 30, 2006 9:48 pm

Re: Whati s happening in your workshop...?

Postby Gearless42 » Sun Jan 22, 2012 12:34 pm

oil drain plug fell out along with all the oil :shock:. So, it was a partial bottom end seize. Needs some new bearings, a pirmary rebuild, a gear shim, some hardware and a gasket set.
If you keep fiddling with it, it's going to fall off...
~Landon
User avatar
Gearless42
 
Posts: 579
Joined: Sat Sep 25, 2010 11:21 am
Location: Eugene, Or

Re: Whati s happening in your workshop...?

Postby jeffreyned » Sun Jan 22, 2012 4:25 pm

Simple oil change on the P today. :) (Prompted by the above post). :lol:
User avatar
jeffreyned
 
Posts: 1219
Joined: Sat May 07, 2011 7:52 pm

Re: Whati s happening in your workshop...?

Postby jeffreyned » Sat Jan 28, 2012 11:09 pm

Installed SeBac front shock today: 8)

Image
User avatar
jeffreyned
 
Posts: 1219
Joined: Sat May 07, 2011 7:52 pm

Re: Whati s happening in your workshop...?

Postby Gearless42 » Thu Feb 16, 2012 9:51 pm

I built your clutch.....
If you keep fiddling with it, it's going to fall off...
~Landon
User avatar
Gearless42
 
Posts: 579
Joined: Sat Sep 25, 2010 11:21 am
Location: Eugene, Or

Re: Whati s happening in your workshop...?

Postby Gearless42 » Thu Feb 16, 2012 9:53 pm

you should go get your jug cut
If you keep fiddling with it, it's going to fall off...
~Landon
User avatar
Gearless42
 
Posts: 579
Joined: Sat Sep 25, 2010 11:21 am
Location: Eugene, Or

Re: Whati s happening in your workshop...?

Postby Tuna Cowboy » Thu Feb 16, 2012 9:54 pm

you mean decked? or cutting to port. i sat for hours in a meeting tonight, would have much preferred to build a clutch. i bet it's cool :D
Cheers,
Geoff
User avatar
Tuna Cowboy
Forum Moderator
 
Posts: 4976
Joined: Mon May 01, 2006 6:21 pm
Location: Eugene, Or

Re: Whati s happening in your workshop...?

Postby Gearless42 » Thu Feb 16, 2012 10:00 pm

decked. your drain hole is fine. I chased the threads and the look great. Need a drain plug though. Most of the motor is back together. need to fix the stator
Last edited by Gearless42 on Thu Feb 16, 2012 10:29 pm, edited 1 time in total.
If you keep fiddling with it, it's going to fall off...
~Landon
User avatar
Gearless42
 
Posts: 579
Joined: Sat Sep 25, 2010 11:21 am
Location: Eugene, Or

Re: Whati s happening in your workshop...?

Postby joe » Sat Mar 10, 2012 3:56 pm

painting a shock, rebuilding a carb, derusting a rim, rebuilding a seat... multi task time!
____________________________________
Friends Don't Let Friends Ride Tupperware
User avatar
joe
Site Admin
 
Posts: 8239
Joined: Tue Apr 25, 2006 10:06 pm
Location: Sunny Eugene, Oregon

Re: Whati s happening in your workshop...?

Postby Gearless42 » Sat Mar 10, 2012 11:30 pm

Cutting some cowls and blasting the layers of paint and bondo off.
If you keep fiddling with it, it's going to fall off...
~Landon
User avatar
Gearless42
 
Posts: 579
Joined: Sat Sep 25, 2010 11:21 am
Location: Eugene, Or

Next

Return to Scooter Workshop

Who is online

Users browsing this forum: No registered users and 1 guest

cron